Month: May 2019

Getting a damp basement is not probably one of the happiest of news possible. It is hard to locate moisture entry into a basement room and one of the most simple test is to tape a piece of aluminum foil to the inside of the walls in the basement and let it be there over night. If in the morning, there is a film of moisture accumulated on the foil, it demonstrates the presence of moisture or points to the need to take preventive steps to clear up the basement.

  1. Concrete sealants

These are typically additives to the concrete cement and brushed on to the walls along with slurry of concrete. They are rather simple to apply and it does not require much of a preparatory work either, it is even possible to brush on the slurry in the presence of a little moisture as well. But the key criterion is to have the mixture dry as fast as possible as it could have a strong bearing on the quality of seal that is formed on the mixture coating.

  1. Silicate based sealers

The silicate sealers are additives that are added to water to be brushed on to the walls outer layer. Most of the cracks and holes are sealed over by the silicate fibers which tend to create an impermeable coat over the surface. But unlike the concrete sealers, the silicate sealers can be used on surfaces that have been painted over and done to a finish. The time taken to affect a complete seal of the surface is much smaller in the case of silicate sealants.

  1. Acrylic paints

Commonly acrylic paints are seen to be used in practically most household paint works but in the case of water proofing, acrylic paints are used to form a sealant surface so that the moisture and dampness is kept out of the basement or other building parts. The main disadvantage of the acrylic paints is that it needs a completely dry surface to be applied to and takes a fair amount of time to dry out too.

If ever there were a strong point to using acrylic paints, then it has to be that there are many shades that are available in the market. Thus there is no dearth of choice and the ability to match the color to the needs of the situation.

  1. Sheets of barriers

The barrier here refers to the layers of plastic or acrylic or even metal that can be placed to prevent the ingress of water at best. Some of the barrier types are screwed onto the walls or even attached with a strong binder to prevent the seepage of water. When it comes to the actual effectiveness of the solutions, it is the quality of the binders that decide on the success of the final solution. It is here that metal sheets like aluminum come to play a strong role in the creation of the barriers.

Having a seeping basement could be one of the most distressing of experiences. Firstly, there is the issue of locating the ingress of the moisture and then comes the issue of having to isolate the seepage and turn out a dry building basement. The two actions are not complementary and needs to be tackled in a systematic manner that would ensure a complete and thorough dryness to be attained.

Dig around

When the seepage is first noticed in a building, the first step is to just dig around the area of the basement. This should expose the outer surface of the basement to the outside to make an assessment of the issue in greater detail. At times the issue could be so apparent that a simple visual perusal could turn out to be the solution that people are looking for. But instances such as these are not much and often it takes a little more of deep digging to bring into the open the issues that have been dormant in the construction. Furthermore, digging around is like an assessment that every team of tree services provider did to all aspects of their services and you can check one great example of this work preference through their website.

Applying the sealants

With water, it does not take much to create the seepage into a building. Just the tiniest of cracks is enough to set into motion the ingress of moisture. Many a times, the concrete cement could lose its cohesiveness to allow water to seep into room.

Sealants can be applied both ways, internally and externally as well. The final choice of the application is situational wise that takes into consideration the final layout of the room base. It really does not matter if the sealant is applied external to the room or internal to the space, but the greater issue of containing the ingress of moisture needs to be addressed adequately.

Another issue with sealants is that there are a number of types of sealants available in the market. The cement based ones, the epoxy ones, the polymer ones and so on.  Each type has its own individual style of application and curing process as well. Some are additives to paint and slurry while others are but stand alone mixtures that needs to be applied individually.

Using the membrane

The membrane is but an elastomeric coating that is applied to form a completely sealed in basement.  It can be applied to both the exterior and the interior of the building basements.  The strong point of the membrane is that it can smoothen over the cracks that occur later on with the shifting or movement of the structure at any time. The elastic polymer can be flexible enough to withstand mild tremors without breaking out the seal on the building.


Rather than use very exotic manner of application or method, it is the simplest application that would work longer and is durable too.  Treatment forms are but methods developed over time and further improvements in technology and their application is to be expected at all times. Increasingly, there has been a fair success to controlling the ingress of moisture to the basements and it is only natural that further improvements in the way solutions are applied are undertaken to the full extent.